By: Amber Grennan On: November 13, 2026 In: Blog Comments: 0

A TMC 400 Li-ion Articulated Crawler Crane was used to support the installation of structural steel for a new mezzanine floor inside an existing warehouse.

Working within a developed industrial building presented several challenges. Access into the working area was restricted, existing columns and production infrastructure reduced the available lifting space, and some steel sections had to be positioned over conveyors and walkways.

With compact dimensions, lithium-ion battery power and an articulated boom, the TMC 400 Li-ion provided a lifting solution suited to working around these restrictions.

Installing Steel Inside an Existing Warehouse

Structural steel installation inside an existing building can be more complex than steel erection on an open construction site.

Rather than working with clear lifting paths, the crane had to operate around the warehouse’s existing layout. Structural columns, overhead services, walkways and barriers all had to be considered when positioning the crane and planning each lift.

MEWPs were also operating alongside the crane to support the steel installation, so their position and movement had to be considered when lifting in close proximity. This added another constraint when coordinating the crane, the load and the installation team within the available working space.

Equipment selection therefore had to consider more than lifting capacity alone. The crane needed to access the internal working area while providing enough flexibility to manoeuvre long steel sections around existing infrastructure and other equipment.

Compact Access for the TMC 400 Li-ion

One of the main access restrictions was a 2,067mm-wide entryway.

With a compact transport width of approximately 1.2m, the TMC 400 Li-ion is well suited to restricted-access environments where larger lifting equipment may be unsuitable.

Its tracked undercarriage also allows the crane to be moved into position before the hydraulic outrigger system is deployed for lifting operations.

This compact design was particularly relevant on this project because the crane needed to operate within an established warehouse rather than an open construction area.

Articulated Lifting Around Conveyors and Walkways

A key advantage of the TMC 400 Li-ion on this installation was its articulated boom design.

Unlike a conventional straight-boom crane, an articulated crane uses multiple boom sections and joints to create a more flexible lifting geometry. This allows the lifting point to be positioned around or beyond obstacles rather than always requiring a direct lifting path.

That capability was important within the warehouse, where some steel sections needed to be lifted over existing conveyors and walkways before reaching their installation positions.

The articulated configuration also provided flexibility when working around structural columns and other existing warehouse infrastructure.

For lighter steel sections requiring additional articulation, the hydraulic jib could be added to provide further reach and flexibility when lifting over or around existing structures.

Main Boom and Hydraulic Jib Configurations

The crane configuration was adapted according to the steel section being installed and the lifting path required.

The heavier beams were lifted using the TMC 400 Li-ion’s main boom, allowing the lifting team to use the most suitable configuration for these loads.

For lighter sections where surrounding structures made access to the installation point more complex, the hydraulic jib was fitted to provide additional reach and articulation.

This allowed the crane configuration to be adapted between lifts rather than relying on the same setup throughout the project.

The TMC 400 Li-ion offers a maximum hook height of 14.8m on the main boom, increasing to 21.1m with the three-section jib, while continuous 360° rotation provides further flexibility when positioning loads around the crane.

Battery-Powered Lifting for an Indoor Environment

As the lifting operations were taking place inside the warehouse, the crane’s lithium-ion battery power was another important consideration.

The electric TMC 400 Li-ion produces zero on-site emissions during operation and offers quieter operation than conventional diesel-powered lifting equipment.

These characteristics are particularly useful for lifting operations inside warehouses, factories and other enclosed industrial buildings, where reducing exhaust emissions and noise at the point of use can be beneficial.

For this project, battery power allowed the crane to combine the lifting capability required for structural steel installation with a power system suited to an indoor working environment.

Radio remote operation also gave the operator greater flexibility to select a suitable working position while controlling the crane and monitoring the load during installation.

Installing the Mezzanine Steel

The structural steel included several long sections that needed to be carefully controlled and positioned within the existing warehouse structure.

The heaviest beam measured 8,807mm long and weighed 616kg, while the heaviest column measured 4,835mm and weighed 344kg.

Although these loads were within the TMC 400 Li-ion’s 4-tonne maximum lifting capacity, their length and the restricted working environment created the main handling challenge.

Long steel sections had to be manoeuvred around existing structures while maintaining control of the load and providing the installation team with the positioning required to connect each section.

The lifting team also had to account for MEWPs working in close proximity to the crane, making careful positioning and coordination particularly important as steel sections were moved into place.

A Flexible Solution for Internal Steel Installation

This mezzanine installation demonstrates how an articulated crawler crane can provide a practical solution when structural steel needs to be installed inside an existing building.

The combination of compact dimensions, lithium-ion battery power and an articulated boom allowed the TMC 400 Li-ion to operate within the restricted warehouse environment while adapting to different steel sections and lifting paths.

For structural steel contractors, mezzanine installers and warehouse fit-out companies working with restricted access or complex internal lifting requirements, GGR Group can provide articulated crawler cranes and specialist lifting solutions to suit the project. Contact GGR Group today to discuss your lifting project needs.

Trackback URL: https://www.ggrgroup.com/news/tmc-400-li-ion-installs-mezzanine-steel-inside-warehouse/trackback/